Automotive hail repair: This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.
First let’s begin with some car paint care tricks: If you can not expose your car to the sunlight, you can use a hair dryer instead. Just aim the hair dryer to the areas you want to fix, and wait until the dents even out. The ideal distance between the hair dryer and the car should be 2-4 inches. While using a hair dryer, there should be an interval of 2 minutes. If the car’s paint starts discoloring, you should stop applying heat right away. Use a rubbing compound or wax to revise the paint color.
If you want to polish your car and are considering buying a buffer, you can see my simplified approach to car polishing for the true beginner to achieve professional results. As the saying goes, “an ounce of prevention is worth a pound of cure”, and your car is no different. If you are just consistent with the basic instructions I have provided here, your car will not only look fabulous year after year, but will retain much more of its original value when you are ready to sell. Want to save your time and maximize your car detailing efforts. Unless you are a die hard car enthusiast, I actually recommend you find a quality, 100% cloth or hand wash, and take your car there at least every 2 weeks and let the crew there perform the grunt work of car washing.
Not only can you unclog a drain with a plunger, but you can also get out small- to medium-sized dents out of your car too. Just splash some water on both the plunger and the dent and start pushing and pulling until it pops out. Make sure to use a cup plunger (for sinks), not a flange one (for toilets). Reversing into an object is one of the easiest ways to get a dent. So for plastic bumpers, even if you attempt to take off the bumper, it might still be difficult to push out the dent because of how stiff the plastic is. Solve this issue by boiling some water in a pot and throwing it on the dent.
Using the Right Wax. Since each type of paint reacts differently to wax and polish, you need to find out which paint was used on your car and purchase detailing products that suit the paint. Some products may act as abrasive agents and strip the car off its original shine. Find extra information at Paint Protection Film Colorado Springs.
Throughout the 1990s, automotive paints and vehicle body materials were high quality and much more resilient to bending. Since both the paint and the body could be bent without significant damage to the paint or permanent damage to the body materials, an entire industry formed based around the concept and technology of repairing dents.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.